* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
We use cookies to provide and improve our services. By using our site, you consent to our Privacy Policy including cookie. Learn more
I have never used Horn, but as I pushed it to try it, I did not ring, so I exchanged it for sure. OEMBracket of BALIUS is strangely constructed, but since it can not be attached to it, every Bracket is exchanged. Size of Horn is about Small about once. It faces downward like OEM and there is no interference. I felt the sound surprisingly large, but OEM has never heard of it before I can compare it. Perhaps it is this kind of thing. It has passed for about a month in Plating version, but it has not rusted yet. The price is also cheap, it is a good product.View Detail
I bought this because my KSR2 OEMHorn stopped sounding.
You can buy a new one for the same price as OEM used one or less, so I think the cost is very high. There is Horn made by other companies in the same price range, but I chose DAYTONABrand of safety and trust because it is the one which cannot be disassembled and repaired basically when the inside breaks down like this time.
The Package includes MADE IN TAIWAN and I personally trust them more than products made in China or other Southeast Asia countries. The material is iron, but the surface is coated with thick plating.
KSR Horn is DC, so I could use it normally. I think it is seldom, but I haven't confirmed whether it sounds when Horn is AC.
There is a nave screw for the adjustment of the example on the reverse side, but it is not written in the instruction manual. Don't spin it, it'll break. It is stated that At any rate, there was no problem in the use with the sound quality as it was without touching anything. It is unconfirmed whether it is possible to adjust it by turning Screw when it stops sounding due to aging or whether it is really damaged if you turn Screw.
In the case of the KSR, remove the 2nd oil tank and work on it. However, if you remove only one of the two screws from the oil tank, the other screw hole will be overloaded and may break. By the way, OEM new products of Oil tank have been discontinued.
The OEM bracket has a rubber damper to prevent vibration, but the screw length of HornBody is too short to use it. If the neck is long, it may become severe in terms of space depending on the type of car, but even the Spring washer of the loosening stopper was difficult to insert, so I thought I would like to set the screw longer by 5-10? In the meantime, I'm tightening it up. We have already installed the countermeasure regulator on our KSR, but we were able to install it without any problem. As for the Nut of Reverse side, there was Space that tightened without a problem with the Twrench of normal Size by removing the Shroud of Right Side.
Because of its location, it is exposed to rain and mud, so I cleaned the terminals well and applied Contact Grease before installing.
The sound quality is larger and thicker than OEM Horn, and it became about a light car. Horn, which is seldom used but is quite impatient when it doesn't ring at the time of need, can be firmly claimed, and I am satisfied.View Detail
Motivation The OEM was functionally OK, but it was Black Painted over rust, so it looked I bought it for the Refresh of [Why Daytonahorn? The OEM Product was discontinued and KIJIMA and POSH etc. were considered, and the OEM Product was made in Black (8 cm in diameter) and the same size as the OEM sound by searching for the sound of the Horn of each company We chose this product as a Installation If you want to replace the OEM bracket with this product, please use the OEM bracket Installed The OEM Bracket is in a state of rust as well as the body, so after hanging the paper, it's ready to be used Black Painted and mounted BracketSize is one size larger than OEMRubber, so OEMRubber I stuffed the packing to prevent it from falling and installed it [Sound Quality] Originally, I bought the GPZ1100 OEMHorn as a close sound because it didn't sound bad It is almost the same sound [Others] As a Universal Product, it has the same quality as the OEM Product, and it has the same quality as the OEM Product I'm very happy with the low price View Detail
เป็นปลอกแฮนด์ที่เอาใส่แฮนด์dax ที่แปลงใช้ใส่honda chalyลวดลายพื้นฐานธรรมดาใส่ได้พอดี แต่พอได้สัมผัสรู้สึกว่าเนื้อค่อนข้างแข็ง ไม่นุ่มมือA hand strap that removes the dax hand. I used to put honda chaly.Basic pattern can be fit. I feel that the meat is quite soft, not soft hands.(translated by Google Translator)View Detail
hook nut is very useful It is convenient to carry luggage and the bike is beautifully decorated.It is necessary for people who like luggage without a luggage. View Detail
Port Usb makes it easy to phone and powerbank.The problem with the battery is gone.But for the safety of motorcycles.Should be connected through a fuse. Relays and Waterproof Switches.View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING