Type: H7 For Hi beam only 12v 20w 6000K Maximum luminous intensity: 35.700cd Equipped with bulb burning out warning canceller
With inspection association certificate
*Install the product correctly according to the instruction manual.Improper installation may result in fire or equipment damage. *Before installation, be sure to disconnect the terminal cord on the minus side of the battery and confirm that the key is OFF. *Please do not touch or get the LED chip dirty.Dirt can cause the LED chip to burn due to heat being built-up. *Please handle this product with care as it is a precision instrument.Do not drop the product or pull the wires forcibly.Improper handling may cause malfunction, injury, burns, or serious accidents that may result in death.In addition, sparks, poor insulation, or short-circuiting may cause a failure of the product or a fire in the vehicle. *Do not disassemble or modify this product in any way.Products that have been disassembled or modified are not covered by warranty. *Do not look directly at the LED light when it is on.It can cause visual impairment. *Do not splash water on the lens while the light is on or immediately after it is turned off.Sudden temperature change may cause damage to the lens or LED bulb.In addition, please do not touch the LED bulb itself, the heat sink behind it, and the controller unit because they get to the high temperature. *This product is only for 12v DC minus common.Be sure to use DC12V as the power source for wiring. *Please do not connect to the AC headlight, which is common in small displacement vehicles. *Minus common refers to the type in which the negative side of the headlight wiring is common to both the Hi beam side and Lo beam side.Not compatible with vehicles with positive common headlights. *As to minibike kits *The kit for minibikes can be used with 12V DC, AC, battery-less *1, minus common *2 and plus common *3 motorcycles. *1. When using the unit on a vehicle with the battery removed, be sure to use the ADC-200 (65016) Battery-less Kit (sold separately). *2. "Minus common" means that the minus side of the headlight wiring is the same for both Hi beam and Lo beam side. *3. "Plus common headlight" refers to the type where the positive side of the headlight wiring is common to both the Hi-beam and Lo-beam sides. *This product is for motorcycles only, so cannot be used on four-wheeled vehicles. *Do not cover with paper or cloth and do not light near flammable materials.Failure to do so may result in fire or abnormal heating.Also, do not light near flammable items such as flammable spray, thinner, etc. or items that may ignite. *Do not install to the headlight with the light on.Failure to do so may result in malfunction or burns. *This product is waterproof for daily life, but it is not completely waterproof.Wrap the coupler coming out of the controller unit with vinyl tape or self-bonding tape, or use caulking agent to waterproof it.Avoid wetting the product with more water than necessary. *When washing a vehicle with a high pressure washer, please do not let the high pressure wash directly hit this product. *Please do not drop the LED bulb or controller unit, or give it a strong shock.It not only causes breakage, deterioration of performance and shortening of service life, but also causes injury. *Be sure to apply the included silicone grease when assembling the LED bulb.Please refer to this manual for details. *Do not touch the LED chip when it is off or on. *Do not cover up the waterproof cooling fan.Make sure that there is enough space behind the fan for the sucked air to flow. *The waterproof cooling fan has a specific orientation for installation.Be sure to install with the silver round seal facing outward. *Use a thread locker to prevent loosening of the threaded part.Periodic retightening is also recommended. *Installation requires expertise and skill.Please have it done at a designated maintenance facility with skilled mechanics. *Please adjust the optical axis before use.It may obstruct the view of oncoming vehicles and cause traffic accidents.
*Neo Factory will not be held responsible for any damage or accident caused by the use of this product.Protec will not be responsible for any labor charges or other costs incurred during repair. *If you feel any abnormality during installation or use, please contact your dealer or PROTEC service department.
After installing the product, be sure to adjust the optical axis using an inspection machine that is compatible with LED (new light source).PROTEC is not responsible for any dirt or clouding of the light lens, scratches, peeling of the reflector plating inside the light, or poor maintenance due to poor optical axis adjustment or age-related deterioration.
This product is for Hi beam only. There is no Hi / Lo switching function, so the light is switched to a single light when the Lo beam is on and the Lo and Hi beams are switched to each other when the HI beam is on.
■By efficiently releasing the heat generated by the LED, the LED can always be lit at full power! LEDs are characterized by their extremely high conversion efficiency (the efficiency of converting input power into visible light [electromagnetic waves with wavelengths that can be seen by the human eye]), but even so, if the input power is 100%, more than 70% is converted into heat.The Cyclone LED series uses a combination of solid aluminum, a heat sink, and a waterproof cooling fan to efficiently dissipate heat and enable full power lighting at all times. Thermal management is essential for heat-sensitive LEDs.If this heat cannot be dissipated efficiently, the power must be reduced from the start of lighting or from the middle of lighting.In other words, if you don't have a good thermal management system, you can't get the full potential of LED.
■Adopts a highly durable waterproof fan! In the Cyclone LED series, Protec also paid attention to the fan which plays an important role in cooling the heat generated by the high power LED efficiently.The fan used for general electronic equipment is not suitable for motorcycles because the bearing of the rotating part is "metal support type" and durability is low.The Cyclone LED series uses a "dual axis ball bearing type" bearing with waterproof performance and excellent durability, which is also used for cooling fans of radiators.It may look small, but it has passed the 20G seismic test for 2 hours!Protech is the only LED bulb for motorcycles that uses a waterproof and durable fan.
■Long life! It has a longer life than H.I.D.
■Power-saving design! Power consumption is 30W for H4 / H4-R type and 20W for H7 type, so it is more energy saving than general H4 halogen bulb (12V 55 / 60W).
■Adoption of reliable CREE LED! Durable and reliable CREE XLamp XP-L LEDs are used for the light emitter.
■Hi / Lo switching! H4 / H4-R type has 3 LEDs for Hi beam and Lo beam respectively and Hi / Lo switching is available.
■Easy to install! It is easy to wire by replacing the valve coupler.
■Bright and quick lighting! Unlike HID, it lights up with full power immediately after power-on.Also, the color of the light does not change gradually like HID.
Points of Attention
* If there may be an instruction manual included, it will be written in Japanese.
* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
Get on your grid by register your motorcycle! About our "Mybike" service
"Easier to Search Items" It helps you to search items to fit for your motorcycle!
"Get Much Valuable Information" It helps you to get special deals, newly listed items and closeouts about your motorcycle!
"Easy to Register" It requires only your motorcycle manufacturer, model name and model year!