-12 *Ask to drill switch holes|* Normal side caps can be used.
GRASS TRACKER
09-12 09-12(FI cars)*Side caps can be used with the stock ones.
GRASS TRACKER
-08 (Carburetor)*Drilling of switch holes is required. |*It is necessary to change the throttle cable, clutch cable and brake hose. |*It is necessary to change the direction of the brake banjo.
GSX400
05-07 GK7CA *Processing of the switch hole is required|* You can use the normal side cap.
Made in Japan.Prototype, installation confirmation and mass production are all under in-house management.These handlebars are made with a great deal of care and attention to detail, including careful selection of materials, several types of polishing, engraving of part numbers, high-precision bending and welding, and high-quality surface treatment, based on technology and know-how cultivated over many years in Osaka in Japan.STKM13A steel material with excellent tensile strength is used.Cleared by JMCA safety standard value.Double anti-corrosion treatment by acrylic coating over black chrome plating.
Points of Attention
* If there may be an instruction manual included, it will be written in Japanese.
Fits: HONDA FTR223 (without side numbers) * Requires modification of the clutch cable and choke cable., HONDA CB750 04- RC42 *Processing of switch hole required|* Required side cap (for 18mm ID), HONDA CB400SF 99-07 NC39 VTEC *Processing of the switch hole is required|* Required side cap (for 18mm ID), HONDA CB400SUPER BOLDOR 05-07 NC39 *Processing of switch hole required|* Required side cap (for 18mm diameter), HONDA CB400SF 99-07 NC39 VTEC III* requires drilling of switch hole|* requires side cap (for 18mm ID)
On the LeftGrip side, there is a paper seal with the product number, ManufacturerMain and product name, which is still difficult to remove. If you could make it easier to peel off, I'd appreciate it. Also, when I peeled off the seal, I found a hole in it. I don't understand why there is a hole in it.
Also, I'd appreciate it if HURRICANE would do an OrderHandlebar or something!View Detail
Fits: HONDA FTR223 (without side numbers) * Requires modification of the clutch cable and choke cable., HONDA CB750 04- RC42 *Processing of switch hole required|* Required side cap (for 18mm ID), HONDA CB400SF 99-07 NC39 VTEC *Processing of the switch hole is required|* Required side cap (for 18mm ID), HONDA CB400SUPER BOLDOR 05-07 NC39 *Processing of switch hole required|* Required side cap (for 18mm diameter), HONDA CB400SF 99-07 NC39 VTEC III* requires drilling of switch hole|* requires side cap (for 18mm ID)
Fits: HONDA FTR223 (without side numbers) * Requires modification of the clutch cable and choke cable., HONDA CB750 04- RC42 *Processing of switch hole required|* Required side cap (for 18mm ID), HONDA CB400SF 99-07 NC39 VTEC *Processing of the switch hole is required|* Required side cap (for 18mm ID), HONDA CB400SUPER BOLDOR 05-07 NC39 *Processing of switch hole required|* Required side cap (for 18mm diameter), HONDA CB400SF 99-07 NC39 VTEC III* requires drilling of switch hole|* requires side cap (for 18mm ID)
Fits: HONDA FTR223 (without side numbers) * Requires modification of the clutch cable and choke cable., HONDA CB750 04- RC42 *Processing of switch hole required|* Required side cap (for 18mm ID), HONDA CB400SF 99-07 NC39 VTEC *Processing of the switch hole is required|* Required side cap (for 18mm ID), HONDA CB400SUPER BOLDOR 05-07 NC39 *Processing of switch hole required|* Required side cap (for 18mm diameter), HONDA CB400SF 99-07 NC39 VTEC III* requires drilling of switch hole|* requires side cap (for 18mm ID)
Reasonably priced item. Seems a fraction bigger than the stock parts. As a result the switch housings and riser clamps appear to have more of a gap between them after installing this bar. The paint also seems very susceptible to scratches. The part that attached to the risers are smooth, not knurled so there is a greater tendency for them to rotate unintentionally. Came packaged in corrugated paper (see attached image). On the w800 these bars give a narrower but more upright feel. if you are using bar end mirrors, take note that the increased swept back angle means that your rear view might not be wide enough.View Detail
Fits: HONDA FTR223 (without side numbers) * Requires modification of the clutch cable and choke cable., HONDA CB750 04- RC42 *Processing of switch hole required|* Required side cap (for 18mm ID), HONDA CB400SF 99-07 NC39 VTEC *Processing of the switch hole is required|* Required side cap (for 18mm ID), HONDA CB400SUPER BOLDOR 05-07 NC39 *Processing of switch hole required|* Required side cap (for 18mm diameter), HONDA CB400SF 99-07 NC39 VTEC III* requires drilling of switch hole|* requires side cap (for 18mm ID)
I feel a lot like Handlebar and it seems to calm down at that time At the time I do not change it with the same Manufacturer There are times when it is not possible to compare what I should do next time In the case of HURRICANE it is rich in variety and easy to select.View Detail
* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
Get on your grid by register your motorcycle! About our "Mybike" service
"Easier to Search Items" It helps you to search items to fit for your motorcycle!
"Get Much Valuable Information" It helps you to get special deals, newly listed items and closeouts about your motorcycle!
"Easy to Register" It requires only your motorcycle manufacturer, model name and model year!