* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
We use cookies to provide and improve our services. By using our site, you consent to our Privacy Policy including cookie. Learn more
I used it to attach CR 38 to SR 400. My SR is a Separate handle, so I used ShortCable of DAYTONA so Manufacturer is different but I made ShortCable. I think that there is no problem if you are replacing the Throttle Cable for installation. One with fixed Nut becomes Reverse Side.
I bought Separate handle used SR to install FCR Carburetor Body. Select Short's -10Centimeter for Separate handle. I thought it might be a bit long at the beginning, but passing through the path of Cable between Forks turned out to be a nice Length. I think that it can be installed easily if it does not mistake even how to take play.View Detail
With FCR carburetor attachment, it attached to the vehicles which have attached SR400 and a Separate handle.Although based also on the umbrella attached to the Separate handle, please adjust die length with an Adjuster if needed. The photograph of management is raised although it is unclear.View Detail
STD Handlebar is completely unnecessary. However, if you have replaced the Handlebar with the Handlebar Up Type, this is a must have part.
I was using the other for VehicleEasyFitBar, and the length of the Normal wire was enough for the Limit, but the Handlebar was too long for the Quantity.:Pair (for Left and Right) I had to replace it because I was getting the symptom that Axel would not return only if I swung it one way or the other.
I would have rated it higher if the platings were a little more careful, but the price is right, so I'll leave it at that.View Detail
First of all, the length of the opening side and the closing side is different by 3cm, but I don't understand the meaning of this difference in length no matter how I install it. It's a pity that the bolt for Throttle side is 13mm head. This is not good.View Detail
I installed POSHSmooth slim line High Solo, but I used it while driving because I pulled the wire too much. I ruptured and bought RepairCable. (-_-;) Setting is completed by carefully adjusting the gap. (⌒∇⌒) After replacing the High Solo, the Axel operation is easy and the response is pleasant. The subtle throttle work is also a treat and the fuel economy is much better. Even if you drive it comfortably on a normal road touring, it will easily exceed 30km per liter. I want to maintain it properly and use it for a long time.View Detail
I used it in the Separate handle days. The OEMAccelerator Wire is too long for the Separate handle.
good point Refreshing as the length of the Cable is adjusted to the Handlebar.
You don't have to worry about getting tangled up because there is no extra Cable.
Axel doesn't falter.
A bad point Even if you don't use the OEMCable, please keep it until you do. Even if you don't use it, keep it until you do.
By adjusting the length of the cable to match the Handlebar, you can maintain the appearance of Refreshing and operability. Keep the OEMCable just in case.View Detail
?attachment The CBR650R is mounted at the same position angle as the NORMAL. However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away. I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose. ・NORMAL (Reserve integrated horizontal master) Impressions of No complaints on public roads. Familiar feel and very easy to handle. However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful. Radipon (Reserve separate body portrait master) Impressions of It was totally different from what I expected, my expectation was that it would feel like a Rear brake… It is really a mild and easy-to-handle radipon. On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN? But I felt the radipon effect from Breaking a little stronger, and It can be hung up to a hard brake without effort. I felt trust that this could stop.View Detail
I purchased this for use with multiple Helmets. 。 Mount included with the BOLD. Microphone and speaker are not included and must be purchased separately.View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING